Bảng Mã Lỗi Xe Nâng Điện TCM – Đèn Báo Lỗi

Liên hệ báo giá

Bảng mã lỗi xe nâng điện TCM – thông tin những ký hiệu thể hiện trên màn hình đồng hồ. Nhìn vào áo kỹ thuật xe nâng có thể phán đoán lỗi và đưa ra phương án khắc phục, sửa chữa.

Chat Zalo

Gọi 0707.886.488

Danh mục: Dịch Vụ Bảo Dưỡng - Sửa Chữa Xe Nâng Tay - Nâng Điện, Sửa Thang Nâng Thuỷ Lực Giá Rẻ Tại TPHCM, Bình Dương, Xe Nâng Điện Cũ Đứng Lái Reach Truck - Ngồi Lái Giá Rẻ Số 1 Tại TPHCM

Mô tả

Bảng mã lỗi xe nâng điện TCM – thông tin những ký hiệu thể hiện trên màn hình đồng hồ.

Bảng mã lỗi xe nâng điện TCM đầy đủ

P0218	Transmission over temperature condition Your transmission is overheating. Some vehicles have a dash light that will say “trans over temp,” but not all vehicles have this feature. This code could mean that the fluid sensor needs to be replaced, but it could also be something far more complex, especially if accompanied by other P codes.
P0613	TCM processor You don’t have to worry much about this code – it’s just telling you that there’s an internal error in the transmission control module (TCM). It’s a programming issue. You can take your car to the dealer and have the TCM replaced.
P0614	ECM/TCM incompatible This is another purely informational code, telling you that the ECM and the TCM aren’t on speaking terms. If you have this code, chances are that one or the other has been recently replaced, and if you installed a used part, it’s not configured to work with the newer part. On newer vehicles, these parts are programmed to work with just one specific vehicle, and can’t be programmed to work with another.
P0700	Transmission control system malfunction Again, this is an informational code. With most vehicles, the TCM is the only computer that can turn on the check engine light. If there’s a problem preventing the light from coming on, you’ll see this cod.
P0706	Transmission Range Sensor Circuit Range/Performance The transmission range sensor conveys information about the gear the vehicle is into the TCM and powertrain control module (PCM). The code may result from defective or corroded manual shift valve linkage, dirty transmission fluid or a defective transmission range sensor. The P0706 code is displayed for vehicles with an automatic transmission.
P0715	Input/Turbine Speed Sensor Circuit Malfunction The transmission’s input speed sensor signals the TCM to enable it to shift the transmission to the proper gear needed for changes in speed. If the TCM is receiving an erratic signal, the P0715 code will be produced. This may be the result of a faulty valve body, engine coolant temperature sensor, shift solenoids or input/turbine speed sensor. This code is specific to vehicles with an automatic transmission.
P0720	Output Speed Sensor Circuit Malfunction This code is generated when the PCM does not receive an adequate signal from the output speed sensor circuit or if there is an abnormal RPM difference between the input RPM sensor and the output speed RPM sensor. It usually indicates that the transmission is slipping. This may be caused by dirty transmission fluid, a faulty engine coolant temperature sensor or defective output speed sensor. The P0720 code is displayed for automatic transmissions.
P0729-P0736	Trouble codes between P0729 and P0736 indicate problems with the gear ratio. Each code specifies the individual gear. These codes may occur if the transmission fluid is low, a clutch in the torque converter malfunctions or if there is a damaged solenoid. All of the above codes are produced by vehicles with an automatic transmission.
P0750-P0770	Solenoid failure can prevent the flow of transmission fluid into the transmission’s hydraulics and cause a gear not to shift properly. If this occurs, a code between P0750 and P0770 will be produced, depending on the gear affected. These codes are produced in automobiles with an automatic transmission.

Bảng lỗi thường gặp xe nâng điện TCM FB-6

(TCM FB-6 Error Codes)

101	Accelerator wire broken
102	Drive motor current sensor defective
103	Drive safety circuit turns on
105	Abnormal plugging of regenerative circuit
106	Controller thermo sensor defective
107	Drive motor current abnomal on the key switch. Trouble occurs during operation.
201	Lift lever sensor wire broken
202	Load handling motor current abnomal
203	Load handling safety circuit turns on
301	Accelerator wire broken
303	Drive safety circuit turns on
401	Lift lever sensor wire broken
403	Load handling safety circuit turns on

Bảng đèn báo lỗi xe nâng TCM đời -7

Display error code Detail of error LED error code

301	Accelerator output defective 17
302	Traveling current sensor output defective 19
303	Drive FET power module short-circuited 01 Drive FET power module open 02 Drive quick charge error 69
305	Drive contactor short-circuited 03
306	Drive contactor open 04
307	Blown main fuse for drive 20
308	Rotation sensor A defective 41 Rotation sensor B defective 42
401	Load handling lift potentiometer defective 35
402	Load handling current sensor output defective 34
403	Load handling FET power module short-circuited 30 Load handling quick charge error 70 Power steering transistor short-circuited 50
404	Load handling FET power module open 31 Power steering transistor open 56
405	Load handling contactor short-circuited 37 Power steering contactor short-circuited 51
406	Load handling contactor open 33 Power steering fuse/contactor open 52
407	Blown main fuse for load handling 45
501	MD contactor drive transistor coil defective 07 F/R switch defective 16 Load dump error (battery overvoltage protection) 86 Load handling contactor drive transistor / coil defective 38 EPROM sum error (Other serious error) 82 EPROMACK error (Other serious error) 83 Power steering contactor drive transistor coil defective 53
502	Drive motor temperature rise 25 Drive motor thermo sensor defective 2 Inching over 67 Drive motor overspeed 91
503	Power steering torque sensor output defective 54
504	Drive controller thermo sensor defective 22 Load handling controller thermo sensor defective 36